Zhejiang Weilan Technology Co., Ltd.

Suntex PC-3110 pH/ORP Transmitter Wiring & Calibration Guide

Author: Zhejiang Weilan Technology Co., Ltd.Source: Official sitePublished: Category: Tech Articles
Summary: Step-by-step wiring diagram overview and two-point calibration procedure for the Suntex PC-3110 pH/ORP transmitter, based on official specs and field troubleshooting practices.

In industrial water treatment and automated chemical dosing skids, the Suntex PC-3110 is one of the most widely installed panel-mounted pH/ORP transmitters thanks to its 96×96 mm cutout and IP65 front protection. Engineers on site frequently need a clear checklist for Suntex PC-3110 wiring and two-point buffer calibration. Based on the official manual and Suntex PC-3110 specifications, this guide covers the essentials from terminal layout to troubleshooting.

1. Key Specifications of Suntex PC-3110

Before wiring, verify that the transmitter matches your panel and process conditions:

  1. Measuring Range: -2.00 to 16.00 pH and -1999 to +1999 mV for ORP with automatic or manual temperature compensation.
  2. Panel Cutout: Compact 96 × 96 mm housing (for larger 144 × 144 mm panels, see the Suntex PC-3310).
  3. Protection & Output: IP65 front panel, isolated 4-20 mA analog output for proportional dosing pump control, and Hi/Lo/Wash relay contacts.

2. Suntex PC-3110 Wiring Terminals Explained

Always disconnect mains power before touching the rear terminal block. Terminals are grouped into four main zones:

Electrode and Temperature Sensor Inputs

  • IN (Measuring Electrode): Connect the high-impedance core wire of the pH/ORP electrode. Keep the signal cable away from VFD or high-voltage power lines.
  • REF (Reference): Connect the outer coaxial shield or dedicated reference lead.
  • TEMP (PT1000 / NTC): Match the temperature compensation wires to the labeled terminals, or switch to manual temperature mode if using an uncompensated sensor.

Power, 4-20 mA Output, and Relays

  • Power Supply (L / N / PE): Confirm nameplate voltage and ensure a solid PE earth ground to prevent drifting readings.
  • 4-20 mA Output (+ / -): Wire directly to a PLC, DCS, or a 4-20 mA controlled metering pump for closed-loop pH dosing.
  • Relay Contacts (Hi / Lo / Wash): Dry contacts for alarm beacons, solenoid valves, or pump start/stop; add an interposing relay for heavy inductive loads.

3. Two-Point Calibration Procedure

Calibrate the Suntex PC-3110 after installing a new sensor or during routine maintenance using fresh pH 7.00 and pH 4.01 (or 10.01) buffers:

  1. Rinse & Blot: Rinse the electrode with deionized water and gently blot the glass bulb dry with tissue (do not rub).
  2. Enter CAL Mode: Press CAL on the front keypad to enter calibration mode.
  3. Zero Point (pH 7.00): Submerge the sensor in pH 7.00 buffer, stir gently, wait for stabilization, and confirm.
  4. Slope Point (pH 4.01 or 10.01): Rinse, blot, submerge in the second buffer matching your process side (acidic or alkaline), and confirm once stable.
  5. Verify Slope: A healthy electrode shows a slope between 85% and 105%. An ERR alert typically indicates aged buffers or a fouled/damaged bulb.

4. Quick Field Troubleshooting

  • Erratic or Stuck Readings: Inspect the REF shield connection and check whether moisture has entered the BNC/terminal connector.
  • 4-20 mA Mismatch: Check the output range mapping (4 mA and 20 mA pH setpoints) inside the setup menu.

Conclusion

Proper Suntex PC-3110 wiring and routine two-point calibration keep your pH/ORP readings stable and protect downstream dosing pumps from over- or under-feeding. For panel integration or compatible sensor selection, contact our engineering team.

FAQ

What is the difference between Suntex PC-3110 and PC-3310?

Both share the same core measurement functions; the PC-3110 uses a 96×96 mm housing while the PC-3310 uses a larger 144×144 mm panel cutout.

Can I splice a standard cable to extend the pH electrode?

No. pH signals have very high impedance and are sensitive to moisture and EMI. Always use dedicated low-noise coaxial extension cable and waterproof connectors.

How often should the PC-3110 be calibrated?

Every 1 to 3 months in clean water, and every 2 to 4 weeks in wastewater or scaling-prone processes.

Why does the transmitter show ERR during calibration?

Common causes include expired buffer solutions, swapped buffers, trapped air bubbles in the glass bulb, or a depleted reference junction.

Can the PC-3110 directly drive a chemical dosing pump?

Yes. Use the Hi/Lo relay contacts for on/off control, or wire the 4-20 mA output to a proportional metering pump.

Get a Quote

Leave your requirements and we will reply within 1 business day

Inquire Now →